Table of Contents
Every kitchen, no matter how modern, needs a make-over at some point. Whether it’s because of wear and tear or because your kitchen installations have grown old, you need to retouch them once in a while to bring out the esthetic that your kitchen deserves. One installation that radiates the beauty of a kitchen is the kitchen faucets. If you want to remove moen kitchen faucet to improve your kitchen condition, then you are in the right place.
For so many people, the thought of replacing their kitchen faucet can be so scary. While some people will even turn to their plumber for help, others will reach out to their friends with the requisite skills to come help them replace the unit. It is entirely not bad reaching out to a friend to come and help you replace your kitchen faucet, however you should not be scared because the process of removing a kitchen faucet is actually not as difficult as you thought.
If you have the right tools you should be through with the process in less than 30 minutes, but as you gain more experience and exposure after reading this article, the process should not take you more than 10 to 15 minutes. One of the benefits of replacing your kitchen faucet by yourself is that you will not only save money and time, you will install the unit the way you want it to be. Plus, the installation will support both hot and cold running water whenever you switch it on.
Ready to remove moen kitchen faucet? Then let’s get started.
Tool Required
- Needle Nose Pliers
- Wrench
- Screwdriver
If you have the above-listed tools readily available in your toolbox, then you are good to go. But if you do not have them you can either borrow them from your neighbours or friends, or dash down to the market to buy yours because you will need them later in the future if you need to make any adjustments or a new installation in your kitchen. Assuming you have these tools available, the following steps will guide you to replace your faulty or leaky Moen kitchen faucet.
Step 1: Shut Off The Waterline
The first step to removing or replacing a faulty Moen kitchen faucet is to shut off the waterline. You need to look for the waterline and trace where the water line valve is and then shut the valve off. In most homes, the water valves for cold water and hot water are usually different, so shut the two valves before you carry on with the next step.
Step 2: Dry The Pipes
Before you start the liver process are you sure the pipes are dry or empty. To do this open the sink valve and check whether or not there is water left in the pipes. If you find any water, quickly drain the water into your cabinets or onto your floor.
Step 3: Extract The Faucet’s Handle
The next step is to extract the Moen faucet’s handle. Pull your screwdriver from your toolbox and apply it in the appropriate place to remove the handle. After removing the handle, a set screw will become visible to you. Make use of the wrench in your toolbox to unscrew it. Once that is done, take off the handle carefully and slowly to avoid any damage.
Step 4: Take Out The Plastic Part
Taking off the plastic part will enable you to see what the issue is with your Moen kitchen faucet. Whether it is a major leak or a broken rubber gasket, you will see it after taking out the plastic part. To take out the plastic part, use the wrench to pull out the small done and a jacket. Once you turn the wrench, the parts will start sliding out.
Step 5: Take Out The Mechanism
The next step is to take out the mechanism. The handle mechanism should be easily removed after removing the plastic sleeve. This unit controls water flow; thus, handle it with care so as to avoid damaging it. There is a screw that secures the mechanism down to the sink. Unscrew the screw to free the mechanism for removal.
Step 6: Take Off The White Ring
There is a white ring under the handle mechanism. The next step is to take off that white ring. You will be able to do this only after removing the mechanism as discussed in step 5 above. As you take off the white ring, apply caution because you will need the white ring back when you replace the unit with a new one or during re-installation. Additionally, you also need to keep the washer underneath the ring safe.
Step 7: Lift The Spout
This is the last step. If you have followed through from step one till now, you won’t have any trouble lifting or removing the spout. It is important to write down the direction of the parts so that during re-installation you won’t find it difficult to couple the unit. You don’t need any tool to remove the spout.
You will find a clip under the spout, use your screwdriver to take off the clip. At this point, the next step is to remove the cartridge. You can either use a cartridge puller or hold the stem using pliers, then spin the unit until the cartridge pulls out. The Moen kitchen faucet should be out.
Final Thoughts
You can see that to remove Moen kitchen faucet is simple and straightforward. You don’t need a plumber to do this, if you have the right tools. Removing or replacing a faulty kitchen faucet comes with lots of benefits. First, you will save money that you would have expended to hire a professional plumber. Secondly, your installation will support both cold and hot running water. So, go ahead and give your kitchen the touch it deserves.
